This caused a bit of confusion for our testers, when funding a channel
the funds are no longer available and listed in `lisfunds`, causing
them to believe funds to have disappeared. This PR adds funds that are
allocated to channels in the `listfunds` output, together with some
info about the channel, to make sure this doesn't happen again.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
The JSON-RPC spec specifies that if the request is unparseable we
should return an error with a NULL id. This is a bit more friendly
than slamming the door in the face.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
As reported by @practicalswift in #945 it is possible to inject
non-printable, or shell escape, characters in a json command, that
will fail to parse and then clear the shell.
Reported-by: @practicalswift
Signed-off-by: Christian Decker <decker.christian@gmail.com>
We get intermittant failure: WIRE_UNKNOWN_NEXT_PEER (First peer not ready)
because CHANNELD_NORMAL and actually telling gossipd that the channel
is available are distinct things: we need both.
(For test_closing_different_fees, we were testing CHANNELD_NORMAL on
the peer, not on l1, too).
But we may also directly send the announcement sigs if the height is
sufficient, so the simplest is to unify the messages.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We save wireaddr to databases as a string (which is pretty dumb) but
it turned out that my local node saved '[::ffff:127.0.0.1]:49150'
which our parser can't parse.
Thus I've reworked the parser to make fewer assumptions:
parse_ip_port() is renamed to separate_address_and_port() and is now
far more accepting of different forms, and returns failure only on
grossly malformed strings. Otherwise it overwrites its *port arg only
if there's a port specified. I also made it static.
Then fromwire_wireaddr() hands the resulting address to inet_pton to
figure out if it's actually valid.
Cc: William Casarin <jb55@jb55.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Now we have wirestring, this is much more natural. And with the
24M length limit, we needn't be so concerned about dumping 64k peer
messages in hex.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
A convenient alias for char *, though we don't allow control characters
so our logs can't be fooled with embedded \n.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
These are now logically arrays of pointers. This is much more natural,
and gets rid of the horrible utxo array converters.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
```
> assert [c['active'] for c in l2.rpc.listchannels()['channels']] == [True, True]
E AssertionError: assert [True, False] == [True, True]
E At index 1 diff: False != True
E Full diff:
E - [True, False]
E + [True, True]
```
We don't actually wait that l2's gossipd has also processed the message.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
`activate_peer` does little more than wiring up some txwatches and
asking `gossipd` to reconnect to the peer. If the peer manages to
reconnect before we activate then we would crash.
This just changes the `assert` causing the crash into a conditional
whether we need to reconnect or not.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
Due to the broadcast failure quite a few users are reporting channels
stuck in awaiting lockin. This commit adds a `dev-forget-channel`
command that checks whether the funding outpoint is in the UTXO, and
forgets the channel if not. The UTXO check can be overridden with the
`force` parameter, but that is dangerous.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
Still writing the channel since some of the channel setup parameters
depends on `chan->id` to be set. If we later set the `chan->id`
signatures fail. This prevents OPENINGD channels showing up after
restarting.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
We were sideloading it, which is awkward, now it's a field that we can
actually use in the code.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
We currently don't handle LOG_IO properly, and we turn it into a string
before handing it to the ->print function, which makes it ugly for
the case where we're using copy_to_parent_log, and also means in
that case we lose *what peer* the IO is coming from.
Now, we handle the io as a separate arg, which is much neater.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Logging often gets called in error paths, so this is just good hygiene.
Also, log_io does this already.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
