Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Changelog-Removed: JSON: `listnodes` `globalfeatures` output (`features` since in 0.7.3).
Changelog-Removed: JSON: `listpeers` `localfeatures` and `globalfeatures` output (`features` since in 0.7.3).
Changelog-Removed: JSON: `peer_connected` hook `localfeatures` and `globalfeatures` output (`features` since in 0.7.3).
Even without optimization, it's faster to walk all the channels than
ping another daemon and wait for the response.
Changelog-Changed: Forwarding messages is now much faster (less inter-daemon traffic)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is a common thing to do, so create a macro.
Unfortunately, it still needs the type arg, because the paramter may
be const, and the return cannot be, and C doesn't have a general
"(-const)" cast.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add new check if we're funder trying to add HTLC, keeping us
with enough extra funds to pay for another HTLC the peer might add.
We also need to adjust the spendable_msat calculation, and update
various tests which try to unbalance channels. We eliminate
the now-redundant test_channel_drainage entirely.
Changelog-Fixed: Corner case where channel could become unusable (https://github.com/lightningnetwork/lightning-rfc/issues/728)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The newly introduced type is used to determine what the call semantics of the
hook are. We have `single` corresponding to the old behavior, as well as
`chain` which allows multiple plugins to register for the hook, and they are
then called sequentially (if all plugins return `{"result": "continue"}`) or
exit the chain if the hook event was handled.
This solves a couple of issues with the need to synchronously drop the
connection in case we were required to understand what the peer was talking
about while still allowing users to experiment, just not kill connections.
We cannot let users use `sendcustommsg` to inject messages that are handled
internally since it could result in our internal state tracking being borked.
This command injects a custom message into the encrypted transport stream to
the peer, allowing users to build custom protocols on top of c-lightning
without requiring any changes to c-lightning itself.
This is needed to fully implement handling of blockheight disagreements
between us and payee.
If payee believes the blockheight is higher than ours, then `pay`
should wait for our node to achieve that blockheight.
Changelog-Add: Implement `waitblockheight` to wait for a specific blockheight.
This is the final step: we pass the complete fee_states to and from
channeld.
Changelog-Fixed: "Bad commitment signature" closing channels when we sent back-to-back update_fee messages across multiple reconnects.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is a transient field, so rework things so we don't leave it in
struct htlc_out. Instead, load htlc_in first and connect htlc_out to
them as we go.
This also changes one place where we use it instead of the am_origin
flag.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Changelog-changed: .lightningd plugins and files moved into <network>/ subdir
Changelog-changed: WARNING: If you don't have a config file, you now may need to specify the network to lightning-cli
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
1. Printed form is always "[<nodeid>-]<prefix>: <string>"
2. "jcon fd %i" becomes "jsonrpc #%i".
3. "jsonrpc" log is only used once, and is removed.
4. "database" log prefix is use for db accesses.
5. "lightningd(%i)" becomes simply "lightningd" without the pid.
6. The "lightningd_" prefix is stripped from subd log prefixes, and pid removed.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Changelog-changed: Logging: formatting made uniform: [NODEID-]SUBSYSTEM: MESSAGE
Changelog-removed: `lightning_` prefixes removed from subdaemon names, including in listpeers `owner` field.
We had a separate logbook for each peer, and copy log entries above
the printable log level into the master logbook. This didn't always
work well, since we didn't dump it on crash for example.
Keep a single global logbook instead, and remove this infrastructure.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
A log can have a default node_id, which can be overridden on a per-entry
basis. This changes the format of logging, so some tests need rework.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If a 'upfront_shutdown_script' was specified, show the address +
scriptpubky in `listpeers`
Changelog-added: JSON API: `listpeers` channels now include `close_to` and `close_to_addr` iff a `close_to` address was specified at channel open
Takes advantage of upfront-shutdown-script to permit users to
specify the close-to address for a channel at open, by adding
a `close_to` field to `fundchannel_start`.
Note that this only is in effect if `fundchannel_start` returns
with `close_to` set -- otherwise, peer doesn't
support `option_upfront_shutdown_script`.
This is mainly an internal-only change, especially since we don't
offer any globalfeatures.
However, LND (as of next release) will offer global features, and also
expect option_static_remotekey to be a *global* feature. So we send
our (merged) feature bitset as both global and local in init, and fold
those bitsets together when we get an init msg.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch adds a channel_id parameter to allow for specifying
channels that are lacking a short_channel_id.
Useful in the case where a peer has 1) multiple channels (ONCHAIN etc)
and 2) a channel where the funding transaction hasn't been
broadcast/mined.
Command format: close id [unilateraltimeout] [destination]
Close the channel with peer {id}, forcing a unilateral
close after {unilateraltimeout} seconds if non-zero, and
the to-local output will be sent to {destination}. If
{destination} isn't specified, the default is the address
of lightningd.
Also change the pylightning:
update the `close` API to support `destination` parameter
Currently the only source for amount_asset is the value getter on a tx output,
and we don't hand it too far around (mainly ignoring it if it isn't the
chain's main currency). Eventually we could bubble them up to the wallet, use
them to select outputs or actually support assets in the channels.
Since we don't hand them around too widely I thought it was ok for them to be
pass-by-value rather than having to allocate them and pass them around by
reference. They're just 41 bytes currently so the overhead should be ok.
Signed-off-by: Christian Decker <@cdecker>
It's generally clearer to have simple hardcoded numbers with an
#if DEVELOPER around it, than apparent variables which aren't, really.
Interestingly, our pruning test was always kinda broken: we have to pass
two cycles, since l2 will refresh the channel once to avoid pruning.
Do the more obvious thing, and cut the network in half and check that
l1 and l3 time out.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
`close` takes two optional arguments: `force` and `timeout`.
`timeout` doesn't timeout the close (there's no way to do that), just
the JSON call. `force` (default `false`) if set, means we unilaterally
close at the timeout, instead of just failing.
Timing out JSON calls is generally deprecated: that's the job of the
client. And the semantics of this are confusing, even to me! A
better API is a timeout which, if non-zero, is the time at which we
give up and unilaterally close.
The transition code is awkward, but we'll manage for the three
releases until we can remove it.
The new defaults are to unilaterally close after 48 hours.
Fixes: #2791
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The reason lnd was sending sync error was that we were taking more than
30 seconds to send the channel_reestablish after connect. That's
understandable on my test node under valgrind, but shouldn't happen normally.
However, it seems it has at least once,
(see https://github.com/ElementsProject/lightning/issues/2847)
: space out startup so it's less likely to happen.
Suggested-by: @cfromknecht
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The spec says to close the channel if they send us an error, but we
need to be more lenient to preserve channels with other
implementations.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We normally reconnect after 1 second: have a flag to say wait for
60. This will be used in the next patch which handles "soft" errors.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Header from folded patch 'channel_fail_transient_slowretry.patch':
fixup! lightningd: add slow_reconnect flag for transient failure.
@ZmnSCPxj points out that function is unsafe, since omitting the bool
parameter still compiled. Make it two separate functions, each
with a distinctive name so every caller has to be fixed.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
And clean up some dev ones which actually happen (mainly by calling
channel_fail_permanent which logs UNUSUAL, rather than
channel_internal_error which logs BROKEN).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Instead of deleting the channels we will simple mark them as `CLOSED` from now
on. This is needed for some of the other tables not to end up with dangling
references that would otherwise survive the channel lifetime, e.g., forwards
and transactions.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
Direct leak of 1024 byte(s) in 2 object(s) allocated from:
#0 0x7f4c84ce4448 in malloc (/lib/x86_64-linux-gnu/libasan.so.5+0x10c448)
#1 0x55d11b782c96 in timer_default_alloc ccan/ccan/timer/timer.c:16
#2 0x55d11b7832b7 in add_level ccan/ccan/timer/timer.c:166
#3 0x55d11b783864 in timer_fast_forward ccan/ccan/timer/timer.c:334
#4 0x55d11b78396a in timers_expire ccan/ccan/timer/timer.c:359
#5 0x55d11b774993 in io_loop ccan/ccan/io/poll.c:395
#6 0x55d11b72322f in plugins_init lightningd/plugin.c:1013
#7 0x55d11b7060ea in main lightningd/lightningd.c:664
#8 0x7f4c84696b6a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x26b6a)
To fix this, we actually make 'ld->timers' a pointer, so we can clean
it up last of all. We can't free it before ld, because that causes
timers to be destroyed.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
I was working on rewriting our (somewhat chaotic) tx watching code
for 0.7.2, when I found this bug: we don't always notice the funding
tx in corner cases where more than one block is detected at
once.
This is just the one commit needed to fix the problem: it has some
unnecessary changes, but I'd prefer not to diverge too far from my
cleanup-txwatch branch.
Fixes: #2352
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We used to produce these, but they're invalid. When we switched to
libwally it (correctly) refuses to get a txid for them.
Fixes: #2772Fixes: #2759
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Move it closer to ccan/json_out, in preparation for using that as a
replacement.
In particular:
1. Add a 'quote' field in json_add_member.
2. json_add_member now always escapes if 'quote' is true.
3. json_member_direct is exposed to allow avoiding of escaping.
4. json_add_hex can use this, so no longer needs to be in json_stream.c.
5. We don't make JSON manually, but always use helpers.
6. We now flush the stream (wake reader) only when we close it, or mark
command as pending.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
"result" should always be an object (so that we can add new fields),
so make that implicit in json_stream_success.
This makes our primitives well-formed: we previously used NULL as our
fieldname when calling the first json_object_start, which is a hack
since we're actually in an object and the fieldname is 'result' (which
was already written by json_object_start).
There were only two cases which didn't do this:
1. dev-memdump returned an array. No API guarantees on this.
2. shutdown returned a string.
I temporarily made shutdown return an empty object, which shouldn't
break anything, but I want to fix that later anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Take into account the fee we'd have to pay if we're the funder, and
also drop to 0 if the amount is less than the smallest HTLC the peer
will accept.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
- Related Changes for `warning` notification
Add a `bool` type parameter in `log_()` and `lov()`, this `bool` flag
indicates if we should call `warning` notifier.
1) The process of copying `log_book` of every peer to the `log_book` of
`ld` is usually included in `log_()` and `lov()`, and it may lead to
repeated `warning` notification. So a `bool`, which explicitly indicates
if the `warning` notification is disabled during this call, is necessary
.
2) The `LOG_INFO` and `LOG_DEBUG` level don't need to call
warning, so set that `bool` paramater as `FALSE` for these log level and
only set it as `TRUE` for `LOG_UNUAUSL`/`LOG_BROKEN`. As for `LOG_IO`,
it use `log_io()` to log, so we needn't think about notifier for it.
Keeping the uintmap ordering all the broadcastable messages is expensive:
130MB for the million-channels project. But now we delete obsolete entries
from the store, we can have the per-peer daemons simply read that sequentially
and stream the gossip itself.
This is the most primitive version, where all gossip is streamed;
successive patches will bring back proper handling of timestamp filtering
and initial_routing_sync.
We add a gossip_state field to track what's happening with our gossip
streaming: it's initialized in gossipd, and currently always set, but
once we handle timestamps the per-peer daemon may do it when the first
filter is sent.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Encapsulating the peer state was a win for lightningd; not surprisingly,
it's even more of a win for the other daemons, especially as we want
to add a little gossip information.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
A new string field is added to the command structure and is specified at the creation of each native command, and in the JSON created by 'json_add_help_command()'.
Keep watching and updating scid until ANNOUNCE_MIN_DEPTH, even when channel is private.
When scid changes, we fail channeld so it will restart and initialize with updated
scid and add it to rtable. Reorgs can change funding tx's height/index after lockin,
which could happen with small minimum_depth=1.
New fields don't have to be spelled out twice.
The raw version are called _only, so we don't miss a call
accidentally. We can rename them when we finally deprecated old
fields.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The original idea is to "tal" channel on the "ctx"(In fact, we'd like to set ctx as "ld").
But we already tal channel on "ld" in new_channel(), so "ctx" is unused.
These are always handed to subdaemons as a set, so group them. This makes
it easier to add an fd (in the next patch).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Without this, the connect command hangs in one of my branches. This logic
is from the old days when gossipd handled connections, and we wanted
to make sure it didn't hang up on this client due to the error.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This seems like overkill, at least for now. Handling the JSON
inline is clearer, for the existing examples at least.
We also remove the dummy hook, rather than fix it.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
I tried to just do gossipd, but it was uncontainable, so this ended up being
a complete sweep.
We didn't get much space saving in gossipd, even though we should save
24 bytes per node.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Adding a giant IO message simply causes it to be pruned immediately,
so truncate it if it's more than 1/64 the max size.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
1. Rename channel_funding_locked to channel_funding_depth in
channeld/channel_wire.csv.
2. Add minimum_depth in struct channel in common/initial_channel.h and
change corresponding init function: new_initial_channel().
3. Add confirmation_needed in struct peer in channeld/channeld.c.
4. Rename channel_tell_funding_locked to channel_tell_depth.
5. Call channel_tell_depth even if depth < minimum, and still call
lockin_complete in channel_tell_depth, iff depth > minimum_depth.
6. channeld ignore the channel_funding_depth unless its >
minimum_depth(except to update billboard, and set
peer->confirmation_needed = minimum_depth - depth).
- This will make a channel loop when 'id' argument was "all".
- The response will now contain an array of objects (peer_id, scid, ...)
- It will skip channels in invalid states.
- Moves iffy channel/peer param stuff to param_channel_or_all
1. amount operations should force you to check validity, rather than
needing a separate call, so make amount_msat_to_u32 return bool,
and WARN_UNUSED_RESULT it.
2. Create a special parsing function for this; not only does this mean
we now only need that one amount call, but also 'check' will correctly
fail with invalid amounts (it only does the parsing step).
3. If we create a primitive which we immediately take(), we allocate it
off NULL to make it clear we expect its lifetime to end here.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
An uncommitted channel should not keep the peer in the db, since the
uncommitted channel isn't in the db itself.
Fixes: #2367
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We need to do it in various places, but we shouldn't do it lightly:
the primitives are there to help us get overflow handling correct.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
As a side-effect of using amount_msat in gossipd/routing.c, we explicitly
handle overflows and don't need to pre-prune ridiculous-fee channels.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Final step for the `peer_connected` hook, we parse the result and act
accordingly. Currently we just close the underlying connection, but we
may want to clean up peers that did not end up with a channel.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
The format is very similar to the one for `listpeers` except we only
list a single channel, and we list the actual netaddr that connected
instead of all known from gossip.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
This used to be inline, but we want to pass channels to hooks as well,
so we just extract this into its own function.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
This hook is used to let a plugin decide whether we should continue
with the connection normally, or whether we should be dropping the
connection. Possible use-cases include policy enforcement (dropping
connections based on previous interactions), draining a node by
allowing only peers with an active channel to reconnect, or
temporarily preventing a channel from making progress.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
We need to still accept it when parsing the database, but this flag
should allow upgrade testing for devs building on top
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We had a bug 0ba547ee10 caused by
short_channel_id overflow. If we'd caught this, we'd have terminated
the peer instead of crashing, so add appropriate checks.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is mainly just copying over the copy-editing from the
lightning-rfc repository.
[ Split to just perform changes prior to the UNKNOWN_PAYMENT_HASH change --RR ]
Signed-off-by: Christian Decker <decker.christian@gmail.com>
Reported-by: Rusty Russell <@rustyrussell>
Error on gcc 7.3.0:
lightningd/peer_control.c: In function ‘json_close’:
lightningd/peer_control.c:955:3: error: ‘channel’ may be used uninitialized in
this function [-Werror=maybe-uninitialized]
channel_set_state(channel,
^~~~~~~~~~~~~~~~~~~~~~~~~~
channel->state, CHANNELD_SHUTTING_DOWN);
Signed-off-by: William Casarin <jb55@jb55.com>
This causes a compiler warning if we don't do something with the
result (hopefully return immediately!).
We use was_pending() to ignore the result in the case where we
complete a command in a callback (thus really do want to ignore
the result).
This actually fixes one bug: we didn't return after command_fail
in json_getroute with a bad seed value.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Usually, this means they return 'command_param_failed()' if param()
fails, and changing 'command_success(); return;' to 'return
command_success()'.
Occasionally, it's more complex: there's a command_its_complicated()
for the case where we can't exactly determine what the status is,
but it should be considered a last resort.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Handers of a specific form are both designed to be used as callbacks
for param(), and also dispose of the command if something goes wrong.
Make them return the 'struct command_result *' from command_failed(),
or NULL.
Renaming them just makes sense: json_tok_XXX is used for non-command-freeing
parsers too.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
These are only supposed to be used when you want the token contents including
surrounding "". We should use this when reporting errors, but usually
we just want to access the tok members directly.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
json_escaped.[ch], param.[ch] and jsonrpc_errors.h move from lightningd/
to common/. Tests moved too.
We add a new 'common/json_tok.[ch]' for the common parameter parsing
routines which a plugin might want, taking them out of
lightningd/json.c (which now only contains the lightningd-specific
ones).
The rest is mainly fixing up includes.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This (will) avoid the plugin having to walk back from the params object
as it currently does.
No code changes; I removed UNUSED and UNNEEDED labels from the other
parameters though (as *every* json_rpc callback needs to call param()
these days, they're *always* used).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is prep work for when we sign htlc txs with
SIGHASH_SINGLE|SIGHASH_ANYONECANPAY.
We still deal with raw signatures for the htlc txs at the moment, since
we send them like that across the wire, and changing that was simply too
painful (for the moment?).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Unlike other daemons, closingd doesn't listen to the master, but runs
simply to its own beat. So instead of responding to the JSON dev_memleak
command, we always check for memory leaks, and make sure that the
python tests fail if they see MEMLEAK in the logs.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
For onchaind we need to remove globals from memleak consideration;
we also change the htlc pointer to an htlc copy, which simplifies
things as well.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We always have an addr entry in the db (though it may be an ephemeral socket
the peer connected in from). We don't have to handle a NULL address.
While we're there, simplify new_peer not to take the features args;
the caller who cares immediately updates the features anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Such an API is required for when we stream it directly. Almost all our
handlers fit this pattern already, or nearly do.
We remove new_json_result() in favor of explicit json_stream_success()
and json_stream_fail(), but still allowing command_fail() if you just
want a simple all-in-one fail wrapper.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It's the only user of them, and it's going to get optimized.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
gossip.pydiff --git a/common/test/run-json.c b/common/test/run-json.c
index 956fdda35..db52d6b01 100644
Some people were alarmed that the state was set to "Loaded from
database" indefinitely. Saying that we are trying to reconnect may be
more informative.
That matches the other CSV names (HSM was the first, so it was written
before the pattern emerged).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We use feerate in several places, and each one really should react
differently when it's not available (such as when bitcoind is still
catching up):
1. For general fee-enforcement, we use the broadest possible limits.
2. For closingd, we use it as our opening negotiation point: just use half
the last tx feerate.
3. For onchaind, we can use the last tx feerate as a guide for our own txs;
it might be too high, but at least we know it was sufficient to be mined.
4. For withdraw and fund_channel, we can simply refuse.
Fixes: #1836
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When in this state, we send a canned error "Awaiting unilateral close".
We enter this both when we drop to chain, and when we're trying to get
them to drop to chain due to option_data_loss_protect.
As this state (unlike channel errors) is saved to the database, it means
we will *never* talk to a peer again in this state, so they can't
confuse us.
Since we set this state in channel_fail_permanent() (which is the only
place we call drop_to_chain for a unilateral close), we don't need to
save to the db: channel_set_state() does that for us.
This state change has a subtle effect: we return WIRE_UNKNOWN_NEXT_PEER
instead of WIRE_TEMPORARY_CHANNEL_FAILURE as soon as we get a failure
with a peer. To provoke a temporary failure in test_pay_disconnect we
take the node offline.
Reported-by: Christian Decker @cdecker
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
For option_data_loss_protect, the peer can prove to us that it's ahead;
it gives us the (hopefully honest!) per_commitment_point it will use,
and we make sure we don't broadcast the commitment transaction we have.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
peer features are only kept for connected peers (as they can change),
but we didn't update them on reconnect. The main effect was that
after a restart we displayed the features as empty, even after
reconnect.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We're about to use the txwatch facility for UTXOs, where there's no channel,
so allow that the be NULL, and hand the struct lightningd which callers
want anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This was a very simple change and allowed us to remove the special
`json_opt_tok` macro.
Moved the callback out of `common/json.c` to `lightningd/json.c` because the new
callbacks are dependent on `struct command` etc.
(I already started on `json_tok_number`)
My plan is to:
1. upgrade json_tok_X one a time, maybe a PR for each one.
2. When done, rename macros (i.e, remove "_tal").
3. Remove all vestiges of the old callbacks
4. Add new callbacks so that we no longer need json_tok_tok!
(e.g., json_tok_label, json_tok_str, json_tok_msat)
Signed-off-by: Mark Beckwith <wythe@intrig.com>
We currently hand the error back to the master, who then stores it for
future connections and hands it back to another openingd to send and exit.
Just send directly; it's more reliable and simpler.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Include it as an optional field in the connect_to_peer message (it was
added before we had optional fields).
The only issue is that reconnects want it too, so again connectd hands
it back to master in connectctl_connect_failed.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
connectd tells master about every disconnection, and master knows
whether it's important to reconnect. Just get the master to invoke a new
connect command if it considers the peer important!
The only twist is timeouts: we don't want to immediately reconnect if
we've failed to connect. To solve this, connectd passes a 'delaytime'
to the master when a connection fails, and the master passes it back
when it asks for a connection.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We used to separate implicit connection requests (ie. timed retries
for important peers) and explicit ones, and send a
WIRE_CONNECTCTL_CONNECT_TO_PEER_RESULT for the latter.
In the success case, that's now redundant, since we hand the connected
peer to the master using WIRE_CONNECT_PEER_CONNECTED; we just need a
message for the failure case. And we might as well tell the master
every failure, so we don't have to distinguish internally.
This also solves a race we had before: connectd would send
WIRE_CONNECTCTL_CONNECT_TO_PEER_RESULT which completes the incoming
JSON connect command, then send WIRE_CONNECT_PEER_CONNECTED. So
there's a window where the JSON command can return, but the peer isn't
known to lightningd yet.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We now simply maintain a pubkey set for connected peers (we only care
if there's a reconnect), not the entire peer structure.
lightningd no longer queries us for getpeers: it knows more than we do
already.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Prior to this, lightningd would hand uninteresting peers back to connectd,
which would then return it to lightningd if it sent a non-gossip msg,
or if lightningd asked it to release the peer.
Now connectd hands the peer to lightningd once we've done the init
handshake, which hands it off to openingd.
This is a deep structural change, so we do the minimum here and cleanup
in the following patches.
Lightningd:
1. Remove peer_nongossip handling from connect_control and peer_control.
2. Remove list of outstanding fundchannel command; it was only needed to
find the race between us asking connectd to release the peer and it
reconnecting.
3. We can no longer tell if the remote end has started trying to fund a
channel (until it has succeeded): it's very transitory anyway so not
worth fixing.
4. We now always have a struct peer, and allocate an uncommitted_channel
for it, though it may never be used if neither end funds a channel.
5. We start funding on messages for openingd: we can get a funder_reply
or a fundee, or an error in response to our request to fund a channel.
so we handle all of them.
6. A new peer_start_openingd() is called after connectd hands us a peer.
7. json_fund_channel just looks through local peers; there are none
hidden in connectd any more.
8. We sometimes start a new openingd just to send an error message.
Openingd:
1. We always have information we need to accept them funding a channel (in
the init message).
2. We have to listen for three fds: peer, gossip and master, so we opencode
the poll.
3. We have an explicit message to start trying to fund a channel.
4. We can be told to send a message in our init message.
Testing:
1. We don't handle some things gracefully yet, so two tests are disabled.
2. 'hand_back_peer .*: now local again' from connectd is no longer a message,
openingd says 'Handed peer, entering loop' once its managing it.
3. peer['state'] used to be set to 'GOSSIPING' (otherwise this field doesn't
exist; 'state' is now per-channel. It doesn't exist at all now.
4. Some tests now need to turn on IO logging in openingd, not connectd.
5. There's a gap between connecting on one node and having connectd on
the peer hand over the connection to openingd. Our tests sometimes
checked getpeers() on the peer, and didn't see anything, so line_graph
needed updating.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Checking in the master doesn't help anything, and it's weird.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
1diff --git a/connectd/connect.c b/connectd/connect.c
index 138b73fc..b01d1546 100644
tal_count() is used where there's a type, even if it's char or u8, and
tal_bytelen() is going to replace tal_len() for clarity: it's only needed
where a pointer is void.
We shim tal_bytelen() for now.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
gossip_getnodes_entry was used by gossipd for reporting nodes, and for
reporting peers. But the local_features field is only available for peers,
and most other fields are only available from node_announcement.
Note that the connectd change actually means we get less information
about peers: gossipd used to do the node lookup for peers and include the
node_announcement information if it had it.
Since generate_wire.py can't create arrays-of-arrays, we add a 'struct
peer_features' to encapsulate the two feature arrays for each peer, and
for convenience we add it to lightningd/gossip_msg.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch guts gossipd of all peer-related functionality, and hands
all the peer-related requests to channeld instead.
gossipd now gets the final announcable addresses in its init msg, since
it doesn't handle socket binding any more.
lightningd now actually starts connectd, and activates it. The init
messages for both gossipd and connectd still contain redundant fields
which need cleaning up.
There are shims to handle the fact that connectd's wire messages are
still (mostly) gossipd messages.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Removed `json_get_params`.
Also added json_tok_percent and json_tok_newaddr. Probably should
have been a separate PR but it was so easy.
[ Squashed comment update for gcc workaround --RR ]
Signed-off-by: Mark Beckwith <wythe@intrig.com>
json_listpeers returns an array of peers, and an array of nodes: the latter
is a subset of the former, and is used for printing alias/color information.
This changes it so there is a 1:1 correspondance between the peer information
and nodes, meaning no more O(n^2) search.
If there is no node_announce for a peer, we use a negative timestamp
(already used to indicate that the rest of the gossip_getnodes_entry
is not valid).
Other fixes:
1. Use get_node instead of iterating through the node map.
2. A node without addresses is perfectly valid: we have to use the timestamp
to see if the alias/color are set. Previously we wouldn't print that
if it didn't also advertize an address.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
structeq() is too dangerous: if a structure has padding, it can fail
silently.
The new ccan/structeq instead provides a macro to define foo_eq(),
which does the right thing in case of padding (which none of our
structures currently have anyway).
Upgrade ccan, and use it everywhere. Except run-peer-wire.c, which
is only testing code and can use raw memcmp(): valgrind will tell us
if padding exists.
Interestingly, we still declared short_channel_id_eq, even though
we didn't define it any more!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Until now, `command_fail()` reported an error code of -1 for all uses.
This PR adds an `int code` parameter to `command_fail()`, requiring the
caller to explicitly include the error code.
This is part of #1464.
The majority of the calls are used during parameter validation and
their error code is now JSONRPC2_INVALID_PARAMS.
The rest of the calls report an error code of LIGHTNINGD, which I defined to
-1 in `jsonrpc_errors.h`. The intention here is that as we improve our error
reporting, all occurenaces of LIGHTNINGD will go away and we can eventually
remove it.
I also converted calls to `command_fail_detailed()` that took a `NULL` `data`
parameter to use the new `command_fail()`.
The only difference from an end user perspecive is that bad input errors that
used to be -1 will now be -32602 (JSONRPC2_INVALID_PARAMS).
Just have a "new depth" callback, and let channeld do the right thing.
This makes the channeld paths a bit more straightforward.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This replacement is a little menial, but it explicitly catches all
the places where we allow a local socket. The actual implementation of
opening a AF_UNIX socket is almost hidden in the patch.
The detection of "valid address" is now more complex:
p->addr.itype != ADDR_INTERNAL_WIREADDR || p->addr.u.wireaddr.type != ADDR_TYPE_PADDING
But most places we do this, we should audit: I'm pretty sure we can't
get an invalid address any more from gossipd (they may be in db, but
we should fix that too).
Closes: #1323
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It does all the other address handling, do this too. It also proves useful
as we clean up wildcard address handling.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
No new functionality, just a continuation of my work toward completing #665.
I removed the common members of `struct withdrawal` and `struct fund_channel`
and placed them in a new `struct wallet_tx`. Then it was fairly straightforward
to reimplement the existing code in terms of `wallet_tx`.
Since I made some structural changes I wanted to get this approved before I
go any farther.
Added 'all' to fundchannel help message.
We're getting spurious closures, even on mainnet. Using --ignore-fee-limits
is dangerous; it's slightly less so to lower the minimum (which is the
usual cause of problems).
So let's halve it, but beware the floor.
This is a workaround, until we get independent feerates in the spec.
Fixes: #613
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When we get a reconnection, kill the current remote peer, and wait for the
master to tell us it's dead. Then we hand it the new peer.
Previously, we would end up with gossipd holding multiple peers, and
the logging was really hard to interpret; I'm not completely convinced
that we did the right thing when one terminated, either.
Note that this now means we can have peers with neither ->local nor ->remote
populated, so we check that more carefully.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Currently we intuit it from the fd being closed, but that may happen out
of order with when the master thinks it's dead.
So now if the gossip fd closes we just ignore it, and we'll get a
notification from the master when the peer is disconnected.
The notification is slightly ugly in that we have to disable it for
a channel when we manually hand the channel back to gossipd.
Note: as stands, this is racy with reconnects. See the next patch.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
(This was sitting in my gossip-enchancement patch queue, but it simplifies
this set too, so I moved it here).
In 94711969f we added an explicit gossip_index so when gossipd gets
peers back from other daemons, it knows what gossip it has sent (since
gossipd can send gossip after the other daemon is already complete).
This solution is insufficient for the more general case where gossipd
wants to send other messages reliably, so replace it with the other
solution: have gossipd drain the "gossip fd" which the daemon returns.
This turns out to be quite simple, and is probably how I should have
done it originally :(
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
1. Lifetime of 'struct reaching' now only while we're actively doing connect.
2. Always free after a single attempt: if it's an important peer, retry
on a timer.
3. Have a single response message to master, rather than relying on
peer_connected on success and other msgs on failure.
4. If we are actively connecting and we get another command for the same
id, just increment the counter
The result is much simpler in the master daemon, and much nicer for
reconnection: if they say to connect they get an immediate response,
rather than waiting for 10 retries. Even if it's an important peer,
it fires off another reconnect attempt, unless it's actively
connecting now.
This removes exponential backoff: that's restored in next patch. It
also doesn't handle multiple addresses for a single peer.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
And on channel_fail_permanent and closing (the two places we drop to
chain), we tell gossipd it's no longer important.
Fixes: #1316
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This will allow us in the next commit to store the transactions that triggered
this event in the DB and thus allowing us to replay them later on.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
d822ba1ee accidentally removed this case, which is important: if the
other side didn't get our final matching closing_signed, it will
reconnect and try again. We consider the channel no longer "active"
and thus ignore it, and get upset when it send the
`channel_reestablish` message.
We could just consider CLOSINGD_COMPLETE to be active, but then we'd
have to wait for the closing transaction to be mined before we'd allow
another connection.
We can't special case it when the peer reconnects, because there
could be (in theory) multiple channels for that peer in CLOSINGD_COMPLETE,
and we don't know which one to reestablish.
So, we need to catch this when they send the reestablish, and hand
that msg to closingd to do negotiation again. We already have code
to note that we're in CLOSINGD_COMPLETE and thus ignore any result
it gives us.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The new connect code revealed an existing race: we tell gossipd to
release the peer, but at the same time it connects in. gossipd fails
the release because the peer is remote, and json_fundchannel fails.
Instead, we catch this race when we get peer_connected() and we were
trying to open a channel. It means keeping a list of fundchannels which
are awaiting a gossipd response though.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We missed it in some corner cases where we crashed/were killed between
being told of the lockin and sending the channel_normal_operation message.
When we were restarted, we were told both sides were locked in already,
so we never updated the state.
Pull the entire "tell channeld" logic into channel_control.c, and make
it clear that we need to keep waching if we cant't tell channeld. I think
we did get this correct in practice, since funding_announce_cb has the
same test, but it's better to be clear.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We'd usually commit to the db soon, but there's a window where it
could be missed.
Also moves loc into the block it's used and make it tmpctx to avoid
an explicit free.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Also report tx and txid, and whether we closed unilaterally or
bilaterally, if we could close the channel.
Also make a manpage.
Fixes: #1207Fixes: #714Fixes: #622
All of the callback functions were only using the tx to generate the txid again,
so we just pass that in directly and save passing the tx itself.
This is a simplification to move to the DB backed depth callbacks. It'd be
rather wasteful to read the rawtx and deserialize just to serialize right away
again to find the txid, when we already searched the DB for exactly that txid.
Signed-off-by: Christian Decker <decker.christian@gmail.com>
I saw a failure in test_funding_fail():
assert l2.rpc.listpeers()['peers'][0]['connected']
This can happen if l2 hasn't yet handed back to gossipd. Turns out
we didn't mark uncommitted channels as connected:
[{'id': '03afa3c78bb39217feb8aac308852e6383d59409839c2b91955b2d992421f4a41e', 'connected': False, 'channels': [{'state': 'OPENINGD', 'owner': 'lightning_openingd', 'funder': 'REMOTE', 'status': ['Incoming channel: accepted, now waiting for them to create funding tx']}]}]
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
So we know how much counterparty could theoretically steal from us
(msatoshi_to_us - msatoshi_to_us_min) and how much we could
theoretically steal from counterparty (msatoshi_to_us_max -
msatoshi_to_us).
For more piloting goodness.
This bug is a classic case of being lazy:
1. peer_accept_channel() allocated its return off the input message,
rather than taking an explicit allocation context. This concealed the
lifetime nature of the return.
2. The context for sanitize_error was the error itself, rather than the
more obvious tmpctx (connect_failed does not take).
The global tmpctx removes the "efficiency" excuse for grabbing a random
object to use as context, and is also nice and explicit.
All-the-hard-work-by: @ZmnSCPxj
As we add more features, the current code is insufficient.
1. Keep an array of single feature bits, for easy switching on and off.
2. Create feature_offered() which checks for both compulsory and optional
variants.
3. Invert requires_unsupported_features() and unsupported_features()
which tend to be double-negative, all_supported_features() and
features_supported().
4. Move single feature definition from wire/peer_wire.h to common/features.h.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This simplifies things, and means it's always in the database. Our
previous approach to creating it on the fly had holes when it was
created for onchaind, causing us to use another every time we
restarted.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
I leave all the now-unnecessary accessors in place to avoid churn, but
the use of bitfields has been more pain than help.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The billboard is now far more useful to tell what's going on, and this
gets us closer to a state == owner mapping.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We always hand in "NULL" (which means use tal_len on the msg), except
for two places which do that manually for no good reason.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We also fold opening_got_hsm_funding_sig() into the caller; it was
previously a callback before we decided to always use the HSM
synchronously.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Because peer_failed would previously drop the connection, we had a
special 'negotiation_failed' message which made the master hand it
back to gossipd. We don't need that any more.
This also meant we no longer need a special hook in read_peer_msg
for openingd to send this message.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
And now we can finally do the db upgrade to remove any OPENINGD
channels once, since we never put them back.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It's giant, but it's encapsulating at least. It is called from the wallet
code when loading channels, or from the opening code when converting
an uncommitted_channel.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Now any struct channel is a genuine channel, the following fields are
always valid:
1. funding_txid: doesn't need to be a pointer.
2. our_msatoshi: doesn't need to be a pointer.
3. last_sig: doesn't need to be a pointer.
4. channel_info: doesn't need to be a pointer.
In addition, 'last_tx' is always valid.
The main effect is to remove a whole heap of branches from the wallet code.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Each peer can have one 'uncommitted' channel, which is in the process
of opening. This is used for openingd, and then on return we convert
it into a full-fledged struct channel and commit it into the database.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This means the caller needs to supply an explicit log to base the
subd log on, and also a callback for error handling.
The callback is kind of ugly, but it gets reworked towards the end
of this series.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Once we rely on the logbook outlasting the peer, we can't refer to the
peer from the logbook function:
Valgrind error file: valgrind-errors.26567
==26567== Invalid read of size 8
==26567== at 0x126297: copy_to_parent_log (peer_control.c:690)
==26567== by 0x11C06B: maybe_print (log.c:253)
==26567== by 0x11C145: logv (log.c:270)
==26567== by 0x11C448: log_ (log.c:319)
==26567== by 0x132951: destroy_subd (subd.c:537)
==26567== by 0x179C19: notify (tal.c:240)
==26567== by 0x17A0CE: del_tree (tal.c:400)
==26567== by 0x17A120: del_tree (tal.c:410)
==26567== by 0x17A4ED: tal_free (tal.c:509)
==26567== by 0x16DEB5: io_close (io.c:443)
==26567== by 0x1328BC: sd_msg_read (subd.c:516)
==26567== by 0x1320AC: read_fds (subd.c:328)
==26567== Address 0x6cf9ca0 is 48 bytes inside a block of size 216 free'd
==26567== at 0x4C30D3B: free (in /usr/lib/valgrind/vgpreload_memcheck-amd64-linux.so)
==26567== by 0x17A1A9: del_tree (tal.c:421)
==26567== by 0x17A4ED: tal_free (tal.c:509)
==26567== by 0x124B6C: delete_peer (peer_control.c:180)
==26567== by 0x12B369: destroy_uncommitted_channel (peer_control.c:2505)
==26567== by 0x179C19: notify (tal.c:240)
==26567== by 0x17A0CE: del_tree (tal.c:400)
==26567== by 0x17A4ED: tal_free (tal.c:509)
==26567== by 0x12B31E: opening_channel_errmsg (peer_control.c:2496)
==26567== by 0x13243A: handle_peer_error (subd.c:407)
==26567== by 0x1326E4: sd_msg_read (subd.c:472)
==26567== by 0x1320AC: read_fds (subd.c:328)
==26567== Block was alloc'd at
==26567== at 0x4C2FB0F: malloc (in /usr/lib/valgrind/vgpreload_memcheck-amd64-linux.so)
==26567== by 0x179C83: allocate (tal.c:250)
==26567== by 0x17A250: tal_alloc_ (tal.c:448)
==26567== by 0x124950: new_peer (peer_control.c:151)
==26567== by 0x12B3EC: new_uncommitted_channel (peer_control.c:2521)
==26567== by 0x12B5C5: peer_accept_channel (peer_control.c:2569)
==26567== by 0x126099: peer_sent_nongossip (peer_control.c:641)
==26567== by 0x113B28: peer_nongossip (gossip_control.c:55)
==26567== by 0x113D9D: gossip_msg (gossip_control.c:144)
==26567== by 0x132783: sd_msg_read (subd.c:487)
==26567== by 0x1320AC: read_fds (subd.c:328)
==26567== by 0x16D1FE: next_plan (io.c:59)
==26567==
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
BackgroundL Each log has a log_book: many logs can share the same one,
as each one can have a separate prefix.
Testing tickled a bug at the end of this series, where subd was
logging to the peer's log_book on shutdown, but the peer was already
freed. We've already had issues with logging while lightningd is
shutting down.
There are times when reference counting really is the right answer,
this seems to be one of them: the 'struct log' share the 'struct
log_book' and the last 'struct log' cleans it up.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We derive the seed from this, so it needs to be unique, but using
rowid forced us to put the channel into the db early, before it
was ready.
Instead, use a counter to ensure uniqueness, initialized when we load
existing peers. This doesn't need to touch the database at all.
As we now have only two places where the channel is committed (the
funder and fundee paths), so we create a new explicit
'wallet_channel_insert()' function: 'wallet_channel_save()' now just
updates.
Note that this also fixes some weirdness in
wallet_channels_load_active: we strangely avoided loading channels in
CLOSINGD_COMPLETE (which fortunately was a transient state, so
unlikely anyone hit this). Note that since the lines above already
delete all the OPENINGD channels, we now simply load them all.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
