Connectd already does this when we *receive* an error or warning, but
now do it on send. This causes some slight behavior change: we don't
disconnect when we close a channel, for example (our behaviour here
has been inconsistent across versions, depending on the code).
When connectd is told to disconnect, it now does so immediately, and
doesn't wait for subds to drain etc. That simplifies the manual
disconnect case, which now cleans up as it would from any other
disconnection when connectd says it's disconnected.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rather than a generic "add member", provide two routines: one which
doesn't quote, and one which does.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We have them split over common/param.c, common/json.c,
common/json_helpers.c, common/json_tok.c and common/json_stream.c.
Change that to:
* common/json_parse (all the json_to_xxx routines)
* common/json_parse_simple (simplest the json parsing routines, for cli too)
* common/json_stream (all the json_add_xxx routines)
* common/json_param (all the param and param_xxx routines)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
connectd is going to end up using this do demux; make it fast and complete.
Fixing this reveals a problem in openingd: it now extracts the channel_id
from funding_signed (which is where we transition off the temporary), and
gets upset. So fix that.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
And turn "" includes into full-path (which makes it easier to put
config.h first, and finds some cases check-includes.sh missed
previously).
config.h sets _GNU_SOURCE which really needs to be done before any
'#includes': we mainly got away with it with glibc, but other platforms
like Alpine may have stricter requirements.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Do proper refcounting on log prefixes; previously we kept them around,
which is fine, but the extra notleak() and backtrace in developer mode
could get quite heavy (I ended up with 1G of backtraces!). This is
mainly due to creating one on every JSONRPC command, and running
clboss.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Changelog-Fixed: lightningd: remove slow memory leak in DEVELOPER builds.
Before:
Ten builds, laptop -j5, no ccache:
```
real 0m36.686000-38.956000(38.608+/-0.65)s
user 2m32.864000-42.253000(40.7545+/-2.7)s
sys 0m16.618000-18.316000(17.8531+/-0.48)s
```
Ten builds, laptop -j5, ccache (warm):
```
real 0m8.212000-8.577000(8.39989+/-0.13)s
user 0m12.731000-13.212000(12.9751+/-0.17)s
sys 0m3.697000-3.902000(3.83722+/-0.064)s
```
After:
Ten builds, laptop -j5, no ccache: 8% faster
```
real 0m33.802000-35.773000(35.468+/-0.54)s
user 2m19.073000-27.754000(26.2542+/-2.3)s
sys 0m15.784000-17.173000(16.7165+/-0.37)s
```
Ten builds, laptop -j5, ccache (warm): 1% faster
```
real 0m8.200000-8.485000(8.30138+/-0.097)s
user 0m12.485000-13.100000(12.7344+/-0.19)s
sys 0m3.702000-3.889000(3.78787+/-0.056)s
```
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
dual funding needs the max-witness-len and utxo fields set for every
input. we should add them when we create a 'fundpsbt', so that every
psbt that c-lightning generates is dual-funding ready
Now that we have json_stream in common/, we can move all the related
helpers from lightningd/json to common/json. This way everyone can
benefit of them (including libplugin, the plugins themselves,
potentially lightning-cli), not lightningd alone!
Note that the Makefile of the common/test/ had to be modified, because
the new helpers make use of common/wireaddr... Which turns out to
\#include <lightingd/lightningd.h> ! So we couldnt just include the .c
and add mocks if we redefined some structs (hello run-param).
Before this patch we used `int` for error codes. The problem with
`int` is that we try to pass it to/from wire and the size of `int` is
not defined by the standard. So a sender with 4-byte `int` would write
4 bytes to the wire and a receiver with 2-byte `int` (for example) would
read just 2 bytes from the wire.
To resolve this:
* Introduce an error code type with a known size:
`typedef s32 errcode_t`.
* Change all error code macros to constants of type `errcode_t`.
Constants also play better with gdb - it would visualize the name of
the constant instead of the numeric value.
* Change all functions that take error codes to take the new type
`errcode_t` instead of `int`.
* Introduce towire / fromwire functions to send / receive the newly added
type `errcode_t` and use it instead of `towire_int()`.
In addition:
* Remove the now unneeded `towire_int()`.
* Replace a hardcoded error code `-2` with a new constant
`INVOICE_EXPIRED_DURING_WAIT` (903).
Changelog-Changed: The waitinvoice command would now return error code 903 to designate that the invoice expired during wait, instead of the previous -2
The tal overhead of 5 pointers, the linked list node is 2; and we also
tal'd the string. That's 96 bytes per entry.
Use a simple array instead, though it means more work on deletion
since each log_entry is no longer a tal object.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
